Desain Simulasi Maksimum Power Point Tracking (MPPT) Metode P&O pada Panel Surya Study kasus Azahra Hidroponik Juata Tarakan | ELECTRONIC THESES AND DISSERTATION
Image of Desain Simulasi Maksimum Power Point Tracking (MPPT) Metode P&O pada Panel Surya Study kasus Azahra Hidroponik Juata Tarakan

Desain Simulasi Maksimum Power Point Tracking (MPPT) Metode P&O pada Panel Surya Study kasus Azahra Hidroponik Juata Tarakan

Pengarang : Wahyudi Siraju - Personal Name;

Perpustakaan UBT : Universitas Borneo Tarakan., 2021
XML Detail Export Citation
    SKRIPSI

Abstract

Di Indonesia, panel surya banyak digunakan untuk menyuplai kebutuhan listrik, dimana kebutuhan listrik bermacam-macam, seperti penerangan lampu, pompa air dan lain-lain. Panel surya ini merupakan pembangkit listrik memanfaatkan energi terbarukan berupa cahaya matahari. Salah satunya di panel surya AZZAHRA HIDROPONIK dengan kapasitas 200 Wp yang juga mempunyai keluaran yang non-linear. Menurut Amri (2015), hal ini disebabkan oleh kondisi matahari yang berubah-ubah. Untuk menyelesaikan masalah non-linear dari panel surya, terdapat 2 jenis controller, yaitu PWM dan MPPT. Pada penelitian ini menggunakan algoritma metode Perturb & Observe (P&O) dikarenakan metode P&O lebih sederhana, memiliki efisiensi yang tinggi dan memiliki tingkat akurasi yang tinggi dibandingkan metode lainnya (Kesler, 2016). Berdasarkan dari hasil simulasi yang dilakukan, maka dapat dikatakan bahwa desain simulasi maksimum power point tracking (MPPT) menggunakan metode perturb and observe (P&O) pada software PSIM berhasil dan MPPT dapat men-track daya maksimum pada panel surya. Pada saat pengaturan kondisi dengan intensitas S = 1000 dan suhu T = 40 °, didapatkan Pmax = 201,5 W, Po = 201,1 W dan waktu yang dibutuhkan MPPT untuk men-track adalah 0,003 detik, pada saat S = 500 T = 25 °, maka didapatkan Pmax = 97,7 W dan Po = 96,4 W dan waktu yang dibutuhkan adalah 0,006 detik. Dan pada kondisi S = 100 T = 10 °, didapatkan Pmax = 9,4 W, Po = 9,3 W dan waktu yang dibutuhkan MPPT untuk men-track adalah 0,04 detik. Setelah didapatkan hasil Desain Simulasi MPPT metode P&0 pada Sel Surya Azzahra Hidroponik, maka didapatkan nilai tegangan, arus, dan daya yang dihasilkan oleh panel surya Azzahra Hidroponik dalam kondisi intensitas dan suhu yang berbeda.

In Indonesia, solar panels are widely used to supply electricity, where electricity needs vary, such as lighting, water pumps and others. This solar panel is a power plant utilizing renewable energy in the form of sunlight. One of them is the AZZAHRA HIDROPONIK solar panel with a capacity of 200 Wp which also has a non-linear output. According to Amri (2015), this is caused by changing sun conditions. To solve the non-linear problem of solar panels, there are 2 types of controllers, namely PWM and MPPT. This study uses the Perturb & Observe (P&O) method algorithm because the P&O method is simpler, has high efficiency and has a high degree of accuracy compared to other methods (Kesler, 2016). Based on the results of the simulations carried out, it can be said that the maximum power point tracking (MPPT) simulation design using the perturb and observe (P&O) method in the PSIM software is successful and MPPT can track the maximum power on the solar panel. When setting conditions with an intensity of S = 1000 and a temperature of T = 40 °, the obtained Pmax = 201.5 W, Po = 201.1 W and the time required for MPPT to track is 0.003 seconds, when S = 500 T = 25 °, the obtained Pmax = 97.7 W and Po = 96.4 W and the time required is 0.006 seconds. And at the condition S = 100 T = 10 °, we get Pmax = 9.4 W, Po = 9.3 W and the time required for MPPT to track is 0.04 seconds. After obtaining the results of the MPPT Simulation Design with the P & 0 method on Azzahra Hydroponic Solar Cells, the values ??of voltage, current and power generated by Azzahra Hydroponics solar panels are obtained under different intensity and temperature conditions.

Detail Informasi