Pengaruh Penambahan Serat Ijuk Terhadap Kuat Tekan Dan Kuat Lentur Beton Mutu K-250 | ELECTRONIC THESES AND DISSERTATION
Image of Pengaruh Penambahan Serat Ijuk Terhadap Kuat Tekan Dan Kuat Lentur Beton Mutu K-250

Pengaruh Penambahan Serat Ijuk Terhadap Kuat Tekan Dan Kuat Lentur Beton Mutu K-250

Pengarang : Randy Khummar Mucitra - Personal Name;

Perpustakaan UBT : Universitas Borneo Tarakan., 2012
XML Detail Export Citation
    SKRIPSI

Abstract

Beton sangat banyak dipakai secara luas sebagai bahan bangunan. Bahan tersebut diperoleh dengan cara mencampurkan semen Portland, air dan agregat dan kadang-kadang bahan tambah (admixture), yang berupa bahan kimia dan bahan alami dengan perbandingan tertentu. Penelitian ini bertujuan untuk mengetahui kuat tekan dan kuat lentur beton dengan bahan tambah serat ijuk dengan berbagai variasi 1% (AR1), 2% (AR2), 3% (AR3), 4% (AR4) dan 5% (AR5), dengan panjang serat ijuk 10 cm. benda uji berupa silinder beton dengan diameter 15 cm dan tinggi 30 cm untuk pengujian kuat tekan masing- masing di buat 10 benda uji pada setiap variasi campuran dan benda uji berupa balok dengan lebat 15 cm tinggi 15 cm dan panjang 60 cm masing-masing dibuat 3 benda uji. Pengujian kuat tekan dan kuat lentur dilakukan setelah benda uji dilakukan perendaman selama 28 hari. Hasil penelitian menunjukan pada kuat tekan beton terjadi peningkatan pada penambahan serat ijuk 1% dengan nilai kuat tekan sebesar 21,042 MPa dan persentase nilai optimal sebesar 0,94%, beton tanpa penambahan serat serat ijuk (beton normal 0%) yaitu 20,844 MPa sedangkan nilai minimum terjadi pada variasi campuran serat ijuk 5% dengan nilai kuat tekan 17,309 Mpa. Hal berbanding terbalik yang terjadi pada pengujian kuat lentur dengan penambahan serat ijuk disetiap variasi campuran mengalami peningkatan dengan nilai terbesar pada 5% terdapat nilai maksimal dari kuat lentur sebesar 5,511 Mpa dengan nilai optimal sebesar 21,19% dan keretakan yang terjadi pada balok termasuk dalam katagori retak lentur.

Concrete is very much widely used as building material. The material obtained by mixing Portland cement, aggregate and water and sometimes the added material (Admixture), in the form of chemicals and natural materials with a certain ratio. This study aims to determine the compressive strength and flexural strength of concrete with fibers as fiber-added materials with different variations of a mixture of 1% (AR1), 2% (AR2), 3% (AR3), 4% (AR4) and 5% (AR5) , a fiber 10 cm. Specimens of concrete cylinder with a diameter of 15 cm and a height of 30 cm for compressive strength testing of each specimen for 10 on any variation of the mix and the test object with a beam width of 15 cm, height 15 cm and a length of 60 cm each specimen were made 3, Testing of compressive strength and flexural strength after immersion test specimens performed for 28 days. The results indicate the concrete compressive strength increases in the addition of 1% fiber with a value of 21.042 MPa compressive strength and the percentage of the optimal value of 0.94%, the concrete without the addition of fiber (0% normal concrete) is 20.844 MPa while the minimum value variation occurred in fiber blend fibers 5% to the value of 17.309 MPa compressive strength. Thing that happens is inversely proportional to the flexural strength testing with the addition fiber in every variation of a mixture of fibers with the largest increase at 5% maximum of flexural strength of 5.511 MPa with the optimal value of 21.19% and cracks that occur on the beam included in the category flexural cracks.

Detail Informasi