Pengaruh Penambahan Serat Kaca (Type E-Glass) Terhadap Kuat Tekan Dan Kuat Lentur Beton Mutu K-250 | ELECTRONIC THESES AND DISSERTATION
Image of Pengaruh Penambahan Serat Kaca (Type E-Glass) Terhadap Kuat Tekan Dan Kuat Lentur Beton Mutu K-250

Pengaruh Penambahan Serat Kaca (Type E-Glass) Terhadap Kuat Tekan Dan Kuat Lentur Beton Mutu K-250

Pengarang : Masdar Moh. Kacil - Personal Name;

Perpustakaan UBT : Universitas Borneo Tarakan., 2012
XML Detail Export Citation
    SKRIPSI

Abstract

Beton memiliki nilai kuat tekan dan kuat tarik yang berbanding terbalik, nilai kuat tarik beton hanya berkisar antara 9% - 15% dari nilai kuat tekannya. Saat ini salah satu alternatif untuk memaksimalkan nilai kuat tarik dari beton itu sendiri adalah penggunaan tulangan pada beton, karena tulangan baja dianggap membuat biaya pengerjaan beton menjadi cukup mahal, sehingga dilakukan penelitian dengan menambahkan serat pada campuran beton. Beton serat dapat didefinisikan sebagai beton yang terbuat dari semen portland, atau bahan pengikat hidrolis lainnya yang ditambah dengan agregat halus dan agregat kasar, air, dan diperkuat dengan serat. Penelitian ini memuat pengujian terhadap beton serat, serat yang digunakan adalah serat kaca (type e-glass) atau dengan nama pasaran serat woven roving no.800. Penelitian ini juga bertujuan untuk mengetahui pengaruh penambahan serat woven roving terhadap kuat tekan dan kuat lentur beton mutu K-250. Untuk menambahkan serat kedalam campuran beton adalah dengan memotong serat dengan panjang maksimal 10 cm. Serat ditambahkan berdasarkan persentase dari berat semen yang digunakan. Variasi penambahan serat adalah 0%, 1%, 2%, 3%, 4%, dan 5%. Benda uji yang digunakan adalah silinder dengan ukuran d = 15 cm, dan h = 30 cm, serta balok dengan ukuran 15 x 15 x 60 cm. Hasil penelitian menunjukkan kuat tekan beton normal adalah 20,84 MPa dan kuat lentur beton normal adalah 4,18 MPa. Kuat tekan maksimum terdapat pada penambahan serat 1% dengan nilai kuat tekan 22,909 MPa dengan peningkatan sebesar 9,01%, serta nilai kuat tekan minimum pada penambahan serat 5% dengan nilai kuat tekan 19,006 MPa dengan penurunan sebesar 8,82 % dari nilai kuat tekan beton normal. Hasil pengujian kuat lentur menunjukkan bahwa dengan menambahkan serat, kuat lentur beton mengalami peningkatan secara signifikan, hasil pengujian kuat lentur maksimum terdapat pada penambahan serat 5% dengan nilai kuat lentur 5,87 MPa dengan persentase peningkatan sebesar 28,79%. Secara umum benda uji balok mengalami keretakkan pada 1/3 tengah bentang dan kemudian terjadi keruntuhan pada benda uji akibat pembebanan yang diberikan tidak mampu ditahan oleh benda uji.

Concrete has a compressive strength value and tensile strength that inverted comparable, concrete tensile strength values ranged only between 9% - 15% of the value of strong compressive. Nowadays one of alternative to maximize that concrete tensile strength itself was reinforcement using in concrete, because concrete reinforcement was considered made concrete processing to be expensive enough, therefore the research undertaken by added the fiber in concrete mix design. Fiber concrete can be defined as concrete that made by portland cement, or the other hidrolis binding material that added by soft aggregate and rough aggregate, water, and reinforced by fiber. This research contained the testing towards fiber concrete, the concrete used was glass fiber (type e-glass) or with trade name is fiber woven roving no. 800. The purpose of this research was to know the effect of adding fiber glass (type e-glass) towards compressive strength and flexural strength of concrete with concrete characteristic K-250. To adding the fiber in concrete mix design was with cut the fiber with maximum length 10 cm. The fiber added based on the percentage from cement weight that used. The fiber adding variation were 0%, 1%, 2%, 3%, 4%, and 5%. Test object that used was cylinder with dimensions d = 15 cm, and h = 30 cm, and the beam dimensions15 X 15 X 60 cm. The research result showed normal concrete compressive strength is 20,84 Mpa and the normal concrete flexural strength is 4,18 Mpa. The maximum compressive strength of fibers found on the addition of 1% by value of 22,909 MPa compressive strength with an increase of 9,01%, and the minimum compressive strength of the fibers on the addition of 5% with a value of 19,006 MPa compressive strength with a decrease of 8,82% of the value of compressive strength normal concrete. Flexural strength test results showed that by adding fiber, flexural strength of concrete has increased significantly, the maximum flexural strength test resultsin the addition of fibers contained 5% by value of 5,87 MPa flexural strength with the percent an increase of 28,79%. In general the beam specimens fractured at 1/3 middle of of the span and then the collapse in the test specimen due to loading can not be retained by the test object.

Detail Informasi